If your Mobile not detect by PC or SPtool, use Meta-Mode

resolve Android Device or Mobile not detect by PC or SPtool problems in Micromax and other Mediatek (MTK) Mobiles by Meta-Mode flashing.

Hi, How to resolve Device or Mobile not detect by PC or SPtool problems in Micromax and other Mediatek (MTK) Mobiles? Meta-Mode is very useful for this problem. Don’t worry if your device not detected by PC or SPtool In this case use Meta-Mode and resolve this problem.

Preparation of Meta-Mode flashing:

1. Make sure proper power backup of your PC
2. Read all steps then do it careful.

Must Read: Simple tips for make your Android phone faster

How to use or flash Mediatek (MTK) Android device by Meta-Mode:

Step 1: Install USB  Driver Download in your PC.

Step 2:  Extract the Stock ROM folder where you want


Step 3: Extract and open the SP Tool. Sptool.exe Run as Administrator

Step 4: Click on Scatter-Loading option.


Step 5: SpTool ask you the location of the scatter file in your PC. You will find it in the extracted Stock ROM folder. Now go to the Rom folder and select the file “Android_scatter_emmc.txt” which is our scatter file.


Step 6: Now click on Download.


Step 7: Connect your Mobile to PC while holding the Volume + button (without battery).


Step 8: SP Tool detect your phone and process will start. Continuous hold the Volume + button till flashing completes. Release Button after 100% Flash.


Step 9: Now start downloading Stock Rom in your phone by flashing


Note: Don’t interrupt this process as it can potentially brick your device. Make sure no power interruption takes place.

Step 10:  After the process complete, a green ring will appear.


Step 11: Insert battery. Start your phone. that’s all

Must Read:  Increase internal memory in Android Mobiles in easy steps

I hope you like this Mobile not detect by PC or SPtool guide from which you will be able to easily flash your stock Rom on your Android device by Meta-Mode flashing process  without any extra efforts. If feel any problem in this guide then please use comment box. Thanks to all.

Note: I am not responsible for Mistakes and Bricked Devices.


  1. hi please i bricked my infinix mtk device and it wont turn on or charge and if i plug it in my pc it is not detected please help me brother

    1. Hi Daniel

      I think your phone battery not charged. so try other way for charge your phone battery. and try different USB cable.

  2. my lenovo A3000 tablet , is stuck on ” erasing” loop after i did my factory reset.
    i installed preloader VCOM . tried flashing, but it does not detect the device.tried with battery removed, it shows lenovo and then vanishes, i tried with vol+ button as you told above, but it doesnt start the download .please note i tried everything in the recovery mode possible .

  3. where do i find the sp flash tools same version with you use in this tutorial and the fastboot rom for xiaomi redmi note 3g (wcdma) global version?

    I downloaded fastboot room from en.miui.com site but its doesnt have the emmc scatter file. The scatter file that include in the fastboot rom is normal scatter file.

    thank you

  4. hi my phone is Micromax a350
    It is working fine except i am not able to reset it by soft or hard method.
    Reason is I can’t enter recovery mode, it just restarts normally when i try to do that.
    Please suggest me what shall i do.
    I want to flash a new ROM but i cant even reset my phone.

  5. After Step 8, I couldn’t follow up..i coudn’t understand what to do in step 9..I connected my phone while clicking all the three buttons, then it showed ‘Download 100% DA’ then i released the buttons and nothing..the same thing remained intact..No yellow downloading started..what to do? plz help..

  6. As instructed above i followed the procedure but it is stucked at Download DA 100%.
    MY phone is Micromax Canvas Xpress 2 E313.
    MY system was vanished because by mistake I clicked on format for a new rom in philtz touch recovery.Please can you tell how to fix this problem.

  7. pllzzzz help me after this process my mobile not give any responde help me plzzzz
    after the flash my mobile it can not respond pllzzzzzz help me

    1. Hi nilesh

      charge your Battery then try boot in recovery and reset your phone, then start

  8. guys i hope someone can help me with a chinese device Cubot S308 that i got super hard bricked and when i try to fix it using SpFTools it always stay stucked on the red 100% bar connecting and disconnecting over and over again without flashing and finish with that "Brom or bram error…helpp

  9. Thank you thanks a lot it's working 100% for me.
    My phone was locked and i'm trying to flash it's very helpful for me.

  10. i followed the above steps but at 87% it stopped with error how to increse the time in meta mode

  11. sir i have to udate in v4 rom for my turbo a250 with may my hang problem will solve sir?

    and i have try all the opyion and switch off and after 1 min insert cable but process do not start what to do

  12. Hello friend,
    In above procedure, you have suggested to click on firmware/download option. But it ask for choosing file. Which file to be selected? You have not cleared this point.

    1. choose scatter file from Rom folder then click on “Firmware Upgrade/Download" option in Sptool

  13. Hello friend,
    In above procedure, you have suggested to click on firmware/download option. But it ask for choosing file. Which file to be selected? You have not cleared this point.

Leave a Reply

Thanks to leave a comment. Please note that all comments are moderated according to our comment policy and your email address will NOT be published. Please Do NOT use keywords in the name field. Lets have a meaningful conversation.